Instant Wireless™SeriesWireless PrintServerUse this guide to install:Model No.:WPS11 ver. 3User Guide
Wireless PrintServer1410. This will display the Configure Printer Port screen. Any installed printerswill be displayed in the Existing Printers field.
16Chapter 5: Bi-Admin:PrintServer ManagementThe Wireless PrintServer is managed by a utility program called Bi-Admin onthe Wireless PrintServer’s Setu
18Obtaining Device Information:The Device Information Icon To access information about the Wireless PrintServer,either click on it in the Device List
20Logical Port Configuration:Logical Port Configuration Icon To set or change the Wireless PrintServer’s logical port set-tings, highlight the Wirele
To disable one of the Wireless PrintServer’s protocols, click once on the DeviceName of the Wireless PrintServer you want to change, and clickConfigur
When the ConfigureServer screen appears,enter the WirelessPrintServer name(SC0222CC is theexample shown inFigure 6-3). Then enteryour password (if yo
Click the Wireless tab to allow you to change information about the WirelessPrintServer. You can configure the SSID, Channel Number, and Network Type
Chapter 7:Advanced PropertiesThe Advanced Properties section of the Web-based Utility is for users who havea thorough understanding of networks and ne
Click the Logical Printers tab to view or change the logical printer settings ofthe Wireless PrintServer. For each Logical Printer, the following fie
Click the SNMP tab to view or change the SNMP settings of the WirelessPrintServer. The Wireless PrintServer supports SNMP (Simple Network ManagementP
COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Instant Wireless is a trademark ofLinksys. Microsoft, Windows, and the Windo
Chapter 8: Internet PrintingProtocol (IPP)IPP (Internet Printing Protocol) is a new standards-based system to allowremote printing from a PC to any ac
4. Click Save to create the IPP port on your system. You will see a messageconfirming that the port has been created, then Figure 8-2: 5. Either selec
2. Select Network Printer and click Next to see the Locate your Printer screen,as shown in Figure 8-4. 3. Select Connect to a printer on the Internet
40Chapter 9:DHCP Support for theWireless PrintServerTo use DHCP, which assigns non-static IP addresses, you must have a DHCPserver and DHCP management
Appendix B: About Bi-DirectionalPrintingNormal printing only sends print signals from a PC to a printer. Bi-direction-al printing, also called bitroni
your printer came with special bi-directional software allowing you to monitorprinter status, do not use it with the Wireless PrintServer—the software
Ethernet - IEEE standard network protocol that specifies how data is placedon and retrieved from a common transmission medium. Has a transfer rate of1
NetBIOS - The native networking protocol in DOS and Windows networks.Although originally combined with its transport layer protocol (NetBEUI),NetBIOS
TCP/IP - Transmission Control Protocol/Internet Protocol (TCP/IP) is thebasic communication language or protocol of the Internet. It can also be useda
Appendix F:EnvironmentalDimensions: 4.76" x 3.74" x 1.18" (121 mm x 95 mm x 30 mm)Unit Weight: 5.6 oz. (0.16 kg)Power: External, 12V DC
Table of ContentsChapter 1: Introduction 1The Instant Wireless PrintServer 1Features 1Package Contents 2Chapter 2: Getting to Know the Wireless Print
54Appendix H: Contact InformationFor help with the installation or operation of this product, contact LinksysTechnical Support at one of the phone num
© Copyright 2002 Linksys,All Rights Reserved.http://www.linksys.com
• One Instant Wireless™ PrintServer• One Antenna using Reverse SMA Connector• One Setup Utility CD-ROM with User Guide • One Power Adapter• One Quick
4LAN This port connects to your wired network using astandard Category 5 (or better) Ethernet cable.Printer This Parallel (LPT) Port connects to your
6Connecting a Printer to the Wireless PrintServer1. Connect your printer to theWireless PrintServer’s Printer(LPT) port with your printer cable.Some p
Wireless PrintServer1. Insert the Setup Utility CD. A built-in autorun will begin the installation ofthe PrintServer’s Bi-Admin Management Utility, an
1. To begin driver installation, click the Start button, select Run, and typeD:\Driver\Win9xnt\setup.exe (where “D” is the letter of your CD-ROMdrive
Wireless PrintServer125. Driver installation is now completed but the Print Driver still needs to beconfigured. Check the box beside Configure Print
Kommentare zu diesen Handbüchern