Linksys EtherFast 10/100 Network In a Box FENSK05 Bedienungsanleitung

10/100 NetworkIn a BoxUse this guide to install thisLinksys product:FENSK05EtherFast 10/100 Network In a BoxEtherFast SeriesUser Guide

5. Carefully slide the EtherFast card into your PC's slot.Make sure that all of its pins are touching the slot's con-tacts. After the card i

Expanding Your Network in the FutureIf you want to add additional computers to your networkin the future, all you need are more EtherFast 10/100cards

Preparing to Install the Software Setting up the EtherFast card's software involvesinstalling a network driver onto your computer. Thedriver will

Windows 98 SetupAfter installing the EtherFast hardware in your comput-er, follow these instructions for installing the networkdriver. The installatio

5. The following window will appear, make sure that"Floppy disk drives" is selected, and click Next to con-tinue.6. Windows will begin searc

Preparing Windows 98 For Use on a Network --Step 1Once you are back at the Windows 98 desktop, you canmake any necessary changes to your system's

Preparing Windows 98 for Use on a Network --Step 2Before enabling File and Printer Sharing, you shouldprepare your computer to be used with any file s

Preparing to Use File and Printer Sharing1. Start up Windows 98. If you are asked to log in, besure to give your correct username and password.2. To s

Enabling File SharingAfter following steps 1-5 on the previous page, double-click on your My Computer icon. A window of avail-able disk drives will ap

How To Share PrintersAfter following steps 1-5 on page 15, double-click onyour My Computer icon. Click on the Printers folder.A window of available pr

COPYRIGHT & TRADEMARKS Copyright © 1999 Linksys, All Rights Reserved. Instant EtherFastis a registered trademark of Linksys. Microsoft, Windows, a

Windows 95 SetupAfter installing the EtherFast hardware in your comput-er, follow these instructions for installing the networkdriver. The installatio

Windows 95 Version A Setup 1. Windows 95 will detect the EtherFast card and dis-play a New Hardware Found window as shown below. 2. Put the EtherFast

Windows 95 Version B Setup 1. While the Update Device Driver Wizard window isvisible, put the EtherFast Card software disk into driveA and click on

Preparing Windows 95 For Use on a Network --Step 1Once you are back at the Windows 95 desktop, you canmake any necessary changes to your system's

Preparing Windows 95 for Use on a Network --Step 2Before enabling File and Printer Sharing, you shouldprepare your computer to be used with any file s

Preparing to Use File and Printer Sharing1. Start up Windows 95. If you are asked to log in, besure to give your correct username and password.2. To s

Enabling File SharingAfter following steps 1-5 on the previous page, double-click on your My Computer icon. A window of avail-able disk drives will ap

How To Share PrintersAfter following steps 1-5 on page 23, double-click onyour My Computer icon. Click on the Printers folder.A window of available pr

Windows NT 4.0 Setup The instructions that follow explain how to set up anNT 4.0 server/workstation.You should have your original Windows NT CD-ROMhan

1. After clicking on Ye s , the Network Setup Wizardwindow will appear. 2. Put a checkmark next to the Wired to the networkoption, then click on Next.

ContentsIntroduction 2About PCI 4Hardware Setup 6Windows 98 Setup 11Windows 95 Setup 18Windows NT 4.0 Setup 26Windows For Workgroups 33Novell NetWare

6. Click Next, then put checkmarks next to all of thenetwork protocols that you want to install. See yourMicrosoft Windows NT user guide(s) or talk to

10. NT will copy the necessary network drivers to yourcomputer. When the copying is complete, you will see alist of installed bindings. You can change

Installing the EtherFast Network Driver in NT 4.0 Since NT networking is already installed, you'll onlyneed to install the EtherFast Card network

6. When NT asks you for the media type or type ofcabling, choose AutoDetect and click OK.7. Choose the services that you want to install. YourMicrosof

10. NT will copy the necessary network drivers to yourcomputer. When the copying is complete, you will see alist of installed bindings. You can change

Windows forWorkgroups SetupAfter installing the EtherFast card hardware in you com-puter, follow the instructions below to install theEtherFast Card&a

After the Sharing window appears, use your mouse toput a checkmark next to any of the following optionsthat you want:...give others access to my files

Novell NetWare SetupThe instructions below cover the following versions of Novell NetWare: · NetWare workstations for DOS & Windows 3.x · Client3

3. When you type install, a new directory called DIAGwill be created on your C: drive, and the DIAG setupand diagnostic program will be copied to it.

During the installation, your AUTOEXEC.BAT andCONFIG.SYS files will be automatically modified. Theold versions of these files will be saved as AUTOEX-

IntroductionIf you've wanted to connect your computers together toshare files, applications, CD-ROM drives, hard disks,printers, and more, look n

Novell Client32 Setupfor Windows 95 and 98Client32 drivers are required for connecting to a 4.x or5.0 server while in Windows 95 only.If you are using

There are currently two versions of Windows 95: · the original release (version A) · a later release (also known as OSR2, or version B) The Client32 i

8. Click on the Other Locations or Specify Locationbutton when it appears. Put the EtherFast card disk intodrive A. Type a:\client32 and press Enter.

Installing a 3.12 ServerThe EtherFast Card network driver is installed duringthe NetWare installation process. During the setup youmay want to refer t

5. At the server command line, type:LOAD c:\LNE100\NBI31X.NLM LOAD c:\LNE100\MSM31X.NLM LOAD c:\LNE100\ETHERTSM.NLM LOAD c:\LNE100\LNE100TX.LAN6. Bi

Installing a 4.x Server The EtherFast Card network driver is installed duringthe NetWare installation process. During the setup youmay want to refer t

Installing a 5.0 ServerFollow these directions to set up a Novell NetWare 5.0server.1. Insert the EtherFast 10/100 LAN Card program diskinto drive A.2

The setup is complete.If you notice excessive “Tx FIFO Underflow” or“Rx FIFO Overflow” counts on your server in theLAN/WAN menu of your driver custom

Wake-On-LANThe EtherFast 10/100 LAN Card supports both MagicPacket and Link Change remote wake-up events.Magic Packet is a type of Wake-On-LAN event d

There are also two different types of Remote Wake-Upcompatible motherboards -- high power and low power.Remote Wake-Up is a little different than PME,

turn on any computer with a WOL network card to per-form after-hours tasks or to access files. The ultimate inmanaged 10/100 networking is yours! If y

Setting Up Your EtherFast LAN Card for Wake-On-LAN Use1. Use the diagram below to locate the WOL pins andthe jumpers on the EtherFast LAN Card.2. Conn

Once your jumpers are set, be sure to write down theMAC address of the network card. It is eithersilkscreened on the card itself or it is noted on a s

AppendixWindows 98 or 95/NT 4.0 Client SetupIf you are installing the EtherFast LAN Card in aWindows 95 or 98 PC that you plan on logging into aNT 4.0

If Access Control is grayed out and cannot be selected,refer to Problem 5 in the Troubleshooting section.7. When you’re done, click OK. When asked if

Novell 3.x Client Setupfor Windows 98 or 95The instructions below explain how to set up the regularNovell NetWare 3.x client for use on a Windows 98 o

Twisted-Pair Cabling There are different grades, or categories, of twisted-paircabling. Category 5 is the most reliable and widelycompatible, and is h

To figure out which wire is wire number 1, hold thecable so that the end of the plastic RJ-45 tip (the partthat goes into a wall jack first) is facing

Troubleshooting Troubleshooting hints for Windows can be found below.If you are using Windows NT, NetWare, or another net-work operating system, skip

Problem 3: The Windows Logon screen doesn’t appearafter you restart your computer.SolutionsClick on Start, Shut Down, then Close All Programsand Logon

Solutions Make sure that the cables are connected correctly. Makesure you are getting Link or Activity lights on both theEtherFast Card and your hub.

About Plug-and-Play PCI TechnologyThe EtherFast 10/100 LAN Card is designed to run in a32-bit desktop computer equipped with PCI expansionslots. The c

Running the Card’sDiagnosticsIf you suspect that there may be a problem with theEtherFast Card, you can use the DIAG diagnostic pro-gram on the EtherF

time. Unless you have two PCs with the same card,don't enable this test.4. When you've selected the desired tests, press Alt-T tobegin the t

Starting Over inWindowsInstalling Windows Network Components fromScratch If you experience installation difficulties, you may needto re-install all of

In some cases, removing one of these components mayin turn automatically remove other components as well.6. For PCs with Dial-Up Networking and/or an

remove Dial-Up Adapter, AOL Adapter, TCP/IP-Compatible Protocol-AOL Adapter or TCP/IP-Compatible Protocol-Dial-Up Adapter.7. When you are done removin

6312. When you’re finished, click on the Close button, shut down Windows, and restart your computer.13. After your computer has restarted, turn to pa

64Manually Installing theNetwork Componentsin WindowsThere may be times when you might need to manuallyinstall missing Windows networking components.

Client for Microsoft Networks If you plan on connecting to an NT file server or peer-to-peer network, click on the Add button. HighlightClient and cli

LEDsLNE100TX EtherFast 10/100 Network CardLINK The card has been successfully connected toa live port on a hub or switchACT Denotes the card’s activit

Specifications Model 10/100 Network In a BoxPart No. FENSK05Standards IEEE 802.3, IEEE 802.3u,PCI 2.1, 2.2, ACPI Card Bus Type 32-bit PCIModes Half an

2. If loading the EMM386.EXE program in your PC'sCONFIG.SYS, you MUST use version MS-DOS 6.22or above. If you load an older EMM386.EXE program(be

Customer SupportFor help with the installation or operation of yourEtherFast 10/100 LAN Card, contact LinksysCustomer Support at one of the phone numb

a Copyright 1999 Linksys, All Rights Reserved.Printed in the USA.http://www.linksys.com

Hardware Setup Before You BeginThe EtherFast 10/100 LAN Cards are equipped with anRJ-45 port that automatically adjusts to either 10Mbpsor 100Mbps spe

Using the Wake-On-LAN FeatureThe EtherFast 10/100 LAN Card supports both MagicPacket and Link Change remote wake-up events.Only install the Wake-On-LA